Login | Join Free

Hotline

4008-655-800

What are the modern chip burning tools? Introduction to programming steps and methods

Date:2021-09-10 14:38:00 Views:2406

Friends who first came into contact with embedded are confused about the concept of programming and burning. In fact, the concept of embedded programming and burning is to write programs into memory, which is similar to downloading in daily life. In fact, burning is a tool for writing data into programmable integrated circuits. Burning is mainly used to write the program (or brush) of the chip, such as single metal tube (embedded) / memory (embedded).

1、 Before IC chip burning procedure, first prepare the following tooling fixtures:

1. Wired electrostatic ring

2. Oily pen

3. Computer

4. Burner (game8 or all-11)

2、 IC chip burning process requirements (precautions):

1. Be careful when placing the IC to avoid damaging the IC and burning base.

2. The IC must not be installed reversely. The IC with the board removed must first check whether there is a tin short circuit on the pin, otherwise it is easy to damage the burning base

3. The burning personnel must be trained before taking the post. Other computer programs must not be used during burning.

4. In case of adverse phenomena, immediately feed back to the management personnel for solution.

现代芯片烧录工具有哪些?编程流程步骤及方法

3、 Steps and methods of IC chip burning program:

1. First connect the data line of the burner and install the corresponding IC base into the burner base; Turn on the computer and the burner.

2. Run the burning software: double click the icon "gang-08" with the mouse (different burning seats correspond to different burning software).

3. Select IC brand: after the program startup screen appears, click the "device" menu to call up the IC brand selection table, then select the brand corresponding to the IC to be burned, and then click "OK";

4. Select IC model: the IC model produced by the company of the IC to be burned appears. Select the IC model and click "run"; At this time, if the burning base wants to select a jumper, press the computer prompt to jumper. After jumping the line, click "OK". If there is no jumper on the burning base, directly enter the burning interface;

5. Transfer in the software to burn: click the menu "file", select "load file to programmer buffer", then select the software to burn, click "open", then select "00", and click OK.

6. Check the software verification code (buffer checksum): after the software is transferred in, a four digit verification code will appear after the buffer checksum, which should correspond to the verification code in the notice of electronic design documents, that is, the software to be burned is correct. If it is incorrect, it shall be immediately fed back to relevant departments for solution.

7. Burning software: click the "program" button to install the IC to be burned into the IC base. After installation, press the burning button on the burning base. When the burning is completed, "OK" will be displayed if the burning is successful, and red "error" will be displayed if the burning fails. The indicator light of each burning base corresponding to the IC with OK burning is on, indicating that the IC has been burned successfully.

8. Make burning marks. Stick stickers on the IC with OK burning. If the burning fails, put it back into other burning seats and burn it again. If it is determined that the IC is damaged, put it into the defective product box and mark it.

4、 Bad IC burning steps:

1. Repeat steps 1 to 6 above;

2. After the burning interface appears, click the "auto" button and select the three options of "erase, program and verify" with the mouse;

3. Install the IC to be burned into the IC base, and then press the burn button on the burn base. When the burning is completed, if the burning is successful, "OK" will be displayed, and if the burning fails, the red "error" character will be displayed. The indicator light of each burn base corresponding to the IC with OK burning is on, indicating that the IC has been burned successfully.

4. Stick stickers on the IC with OK burning. If the burning fails, put it back into other burning seats and burn it again. If it is determined that the IC is damaged, it can be returned to the warehouse.

5、 IC burning verification steps:

1. Before going to work every day, put the IC to be burned into the IC burning base, burn the IC according to the operation instructions and number it

2. After the burning is successful, put the IC into other burning bases with different numbers, then select "verify" in the menu and press "run" to start the verification. If "OK" appears in all, put the IC into other burning bases for re verification. If the verification is OK, it indicates that the burning base is OK

3. If "verify" fails, first install the IC with OK verification of other seats into the IC seat corresponding to the IC with failed burning and the seat with failed verification just now. If a seat still fails to verify, it indicates that the seat may be damaged, resulting in error in burning IC data, and put it into the IC Verification with OK verification of other seats again. If it is confirmed that there is damage, stop burning the seat immediately. And will immediately report the situation to relevant personnel and recheck the burned IC.

The above is the related content of "modern chip burning steps and methods" brought by the core detection. Through this article, I hope it can be helpful to you. If you like this article, you might as well continue to pay attention to our website, and we will bring more wonderful content later. If you have any needs related to the inspection and testing of electronic products, please call Chuangxin testing, and we will serve you wholeheartedly.